on FAQ

What causes a car to overheat with no leaks?

What causes a car to overheat with no leaks?

The main cause of an overheating engine with no leaks is a faulty water pump, a broken thermostat or a blocked radiator.

Why is my car still overheating after changing thermostat?

Why is my car overheating with a new thermostat? Your car could be overheating with a new thermostat for a variety of reasons including a faulty water pump, worn belt, clogged radiator, faulty radiator cap or air in the cooling system.

Why is my Mitsubishi Eclipse overheating?

While there are a variety of reasons your Mitsubishi Eclipse is overheating, the most common 3 are a coolant leak (water pump, radiator, hose etc.), the radiator fan, or a failed thermostat. Coolant leak (water pump, radiator, hose etc.)

How do you troubleshoot an overheating engine?

Part 1 of 1: Troubleshooting the overheating condition

  1. Materials Needed.
  2. Step 1: Check the coolant level and radiator cap.
  3. Step 2: Make sure there is no air in the system.
  4. Step 3: Verify that the radiator fans are spinning.
  5. Step 4: Test the fan motor.
  6. Step 5: Check the serpentine belt.
  7. Step 5: Check for leaks.

Why would my car overheat but the heater blows cold air?

If your car is overheating but you are only getting cold air from the heater then this could be a sign of a blockage in the engine cooling system. If the coolant flow is restricted, this will cause the engine to run hot or overheat. Another common cause of this problem is a faulty engine thermostat.

Why is my car overheating even with coolant?

If you coolant isn’t circulating through your engine correctly it will begin to overheat. Even if you don’t have a leak over time coolant can evaporate or get clogged with particles causing it to circulate incorrectly. The hoses that circulate your coolant can become eroded, clogged, or detached over time.

What to do after replacing a thermostat?

After replacing the thermostat, refill antifreeze. Leave the radiator cap off, and start the vehicle. Wait five minutes to allow all of the antifreeze to circulate throughout the engine. Turn off the engine, and allow the engine to cool.

What are the symptoms of a bad thermostat?

Leakage from the mounting surface. Appearance: Seepage, drips or large coolant bleed marks on or around the mounting surface or on the housing.

  • Rust and corrosion. Appearance: Rust and corrosion on the surfaces of the thermostat.
  • Deposit build-up.
  • Map-controlled thermostats.

    • What are 10 common causes of overheating?

    What are 10 common causes of overheating?

    • Too little or no coolant. Driving without proper levels of coolant/antifreeze may cause a coolant system failure.
    • Cooling system leaks.
    • A broken water pump.
    • Radiator issues.
    • Oil too low.
    • Thermostat failure.
    • Issues with the belts and hoses.
    • Heater core is plugged up.

    What are the signs of a bad thermostat?

    5 Symptoms of a Bad Thermostat (and Replacement Cost)

    • #1 – Temperature Gauge Reading Higher (or Lower) Than Normal.
    • #2 – Sudden Air Temperature Changes Inside Vehicle.
    • #3 – Coolant Leaking.
    • #4 – Rumbling Noises.
    • #5 – Heater Malfunction.

    Can a faulty thermostat cause overheating?

    Faulty Thermostat Once the engine reaches operating temperature, the valve will open and coolant will begin to flow through the engine. A faulty thermostat might remain closed even when the engine is hot, which can quickly lead to overheating.

    How do you fill coolant after changing thermostat?

    add the coolant to the reservoir to the fill line, leave the cap off, turn on the engine. add coolant as the level goes down. once it stop going down usually about 5-10 min put the cover back on. take it for a short drive and check the level to make sure its stabilized.